基本描述

产品名称

重组单体链霉亲和素（r-mSA）

别名

单体链霉亲和素 | 抗生物素蛋白 | 抗生物素蛋白链霉菌 | 重组单体链霉亲和素

英文别名

Monomeric Streptavidin | Streptavidin | SA | Recombinant Monomeric Streptavidin | rm-SA

规格或纯度

BioReagent, 用于蛋白分析, for ELISA, 适用于免疫组织化学, ≥95%(SDS-PAGE), ≥8U/mg

产品介绍

分子量：15.1 kDa

物理外观： Lyophilized

储存缓冲液： Lyophilized from 10mM CBS, Trehalose, pH 9.2

复溶(Reconstitution)：Reconstitute in sterile distilled water. Stock solutions should be apportioned into working aliquots and stored at ≤ -20 °C. Further dilutions should be made in appropriate buffered solutions.

产品描述：

链霉亲和素（Streptavidin，SA）是阿维丁链霉菌（Streptomyces avidinii）在生长过程中分泌的一种同型四聚体蛋白。同亲和素一样，一摩尔的链霉亲和素可以结合四摩尔的生物素，与生物素具有很高的亲和力。由于 SA 不含糖基且等电点接近于中性，因此 SA 在检测应用中具有比亲和素更低的非特异性结合水平。

该制品已被广泛应用于多种生物技术领域，诸如：包被免疫检测用微孔板，制备 SA 偶联酶制剂，SA 偶联荧光素、SA 偶联磁珠等，进而参与酶联免疫吸附和酶催化放大实验，免疫组化化学、生物分子纯化、生物传感器、生物纳米微球、预靶向制药研究和生物芯片被料等。该重组单体链霉亲和素具有易洗脱，空间位阻小，提高了偶联效率等优点。 (该重组单体链霉亲和素N端含His-Tag 标签，等电点为 7.1，接近中性)

阿拉丁链霉亲和素系列产品：

货号	产品名称	物理外观	储存缓冲液	分子量	来源	活性（U/mg蛋白）	关键特性
S274235	重组链霉亲和素 (r-SA)	Lyophilized	Lyophilized from 5mM PBS, pH 6.0	62.4kDa (tetramer), 16.5kDa (monomer)	E.coli	≥15	C端含His-Tag；pI=6.42
R748131	重组单体链霉亲和素（r-mSA）	Lyophilized	Lyophilized from 10mM CBS, Trehalose, pH 9.2	15.1kDa	E.coli	≥8	N-His tag，pI=7.1，易洗脱
S767455	重组增强稳定型核心链霉亲和素（se-cSA）	Lyophilized	Lyophilized from 5mM PPB, Trehalose, pH 7.4	53.6kDa (tetramer), 13.4kDa (monomer)	E.coli	17-19	核心序列优化，序列修饰，热稳定性、溶解性、活性等提升；pI=5.68
S767462	重组粘性链霉亲和素 (r-ScSA)	Lyophilized	Lyophilized from 5mM PBS, pH 7.4	54-94kDa	E.coli	≥14	增强吸附性（特别适用于NC膜），保留核心活性
R767460	重组核心链霉亲和素 (r-cSA)	Lyophilized	Lyophilized from 5mM PBS, pH 7.4	54kDa (tetramer), 13.5kDa (monomer)	E.coli	≥15	核心序列优化；C端含半胱氨酸；pI=6.04
R767461	重组核心链霉亲和素2 (r-cSA2)	Lyophilized	Lyophilized from 5mM PBS, pH 7.4	53.2kDa (tetramer), 13.3kDa (monomer)	E.coli	≥16	核心序列优化；pI=6.09
R767452	重组核心链霉亲和素4 (r-cSA4)	Lyophilized	Lyophilized from 5mM PPB, Trehalose, pH 7.4	55.2kDa (tetramer), 13.8kDa (monomer)	E.coli	≥16	核心序列优化，序列修饰（增加了氨基的含量），稳定性、溶解性等提升；pI=8.93
R767450	重组长臂巯基核心链霉亲和素	Lyophilized	Lyophilized from 20mM HEPES, Trehalose, TCEP, pH 7.0	54.8kDa (tetramer), 13.7kDa (monomer)	E.coli	≥16	核心序列优化，C端的半胱氨酸前添加6个柔性氨基酸延长巯基臂；pI=6.09

使用方法：（仅供参考）
由于产品生产工艺中冻干环节会引入保护剂等，为减少您的实验误差，建议先通过内部检测方法，产品中蛋白进行准确定量后，再进行后续实验，并按实际情况进行产品用量调整。建议优先选择紫外吸收法进行定量，方法如下：
将样品从低温条件下拿出后，平衡至室温，并擦去瓶外附着的冷凝水，小心打开瓶盖，防止干粉飞溅损失。用去离子水或缓冲液进行复溶，充分溶解后，稀释至合适浓度，小心移入比色皿中，以去离子水或缓冲液为空白对照，测定样品在 280 nm 处的吸光值（建议吸光值控制在 0.1-1.5区间内），将其代入以下公式计算蛋白质浓度：

式中：C：样品原液的蛋白质质量浓度（mg/mL）

A280nm：蛋白质溶液在 280nm 处测得的吸光值

N：稀释倍数

E(0.1% at 280nm)：1 mg/mL 蛋白质的消光系数

例如将本产品冻干粉充分溶解并混匀后，取适量原液稀释 10 倍，测得其在 280 nm 处的吸光值为0.7269，则原液的蛋白浓度为 10×0.7269/2.423=3 mg/mL。
注意事项：
1. 链霉亲和素冻干粉易溶于水，溶解性可达 10 mg / mL 或更高；
2. 建议使用纯水溶解；
3. 如有未溶解物质，建议延长复溶时间。也可以通过离心或其他方式除去不溶物后，再用于后续实验，不会对总蛋白产生很大的影响。
4. 考虑到蛋白质特殊性，冻干粉建议现用现配，溶解后应避免反复冻融，如需多次使用，建议按需分装后冻存（-20°C）；不建议在 4°C下长期存放。

M：蛋白质分子量标准
Lane 1：重组单体链霉亲和素（还原）
Lane 2：重组单体链霉亲和素（非还原）

Molecular weight: 15.1 kDa

Physical appearance: Lyophilized

Buffer storage: Lyophilized from 10mM CBS, Trehalose, pH 9.2

Reconstitution：Reconstitute in sterile distilled water. Stock solutions should be apportioned into working aliquots and stored at ≤ -20 °C. Further dilutions should be made in appropriate buffered solutions.

Source
E. coli fermentation engineering strain

Product introduction:

Streptavidin (SA) is a homologous tetramer protein secreted by Streptomyces avidinii during its growth. As with avidin, one mole of streptavidin can bind four moles of biotin, and biotin has a high affinity. Because SA does not contain a sugar group and has a near neutral isoelectric point, SA has a lower non-specific binding level than avidin in detection applications. The product has been widely used in a variety of biotechnology fields, such as: Coated with microporous plates for immunoassay, preparation of SA coupled enzyme preparations, SA coupled fluorescein, SA coupled magnetic beads, etc., and then participate in enzyme-linked immunoadsorption and enzyme catalytic amplification experiments, immunohistochemistry, biomolecular purification, biosensors, biological nanospheres, pre-targeted pharmaceutical research and biochip materials. The recombinant monomer streptavidin has the advantages of easy elution, low steric hindrance and high coupling efficiency. (The N-terminal of the recombinant streptavidin contains His Tag, and the isoelectric point is 7.1, which is close to neutral)

Method of use (for reference only)
Due to the introduction of protective agents in the freeze-drying process of the product, in order to reduce your experimental error, it is recommended to first pass the internal detection method, and accurately quantify the protein in the product, and then conduct follow-up experiments, and adjust the product dosage according to the actual situation. It is recommended that UV absorption method be preferred for quantification, as follows:
After taking the sample out of the low temperature condition, balance to room temperature, and wipe away the condensed water attached to the outside of the bottle, and carefully open the bottle cap to prevent the loss of dry powder splash. Redissolve with deionized water or buffer, after fully dissolved, dilute to a suitable concentration, and carefully move into the cuvea, using deionized water or buffer as a blank control, determine the absorbance value of the sample at 280 nm (it is recommended that the absorbance value be controlled within the range of 0.1-1.5), and substitute it into the following formula to calculate the protein concentration:

C: Protein mass concentration of the sample stock solution (mg/mL)
A280nm: The absorption value of the protein solution measured at 280nm
N: dilution ratio
E(0.1% at 280nm) : extinction coefficient of 1 mg/mL protein

For example, after the freeze-dried powder of the product is fully dissolved and mixed, the appropriate amount of the stock solution is diluted 10 times, and the absorption value at 280 nm is 0.7269, then the protein concentration of the stock solution is 10×0.7269/2.423=3 mg/mL.

Note:
1. Streptavidin freeze-dried powder is easily soluble in water, with a solubility of 10 mg/mL or higher;
2. It is recommended to use pure water to dissolve;
3. If there are undissolved substances, it is recommended to extend the re-dissolution time. The insoluble matter can also be removed by centrifugation or other means, and then used in subsequent experiments, and will not have a great impact on the total protein.
4. Considering the particularity of protein, freeze-dried powder is recommended to be used on the go. Repeated freeze-thawing should be avoided after dissolution. If it is needed for multiple uses, it is recommended to be frozen after packaging as required (-20°C); Long-term storage at 4°C is not recommended.

M: Protein molecular weight standard
Lane 1: Recombinant monomer Streptavidin (reduced)
Lane 2: Recombinant Monomer Streptavidin (non-reduced)

偶联

Unconjugated

储存与运输

物理形态	冻干(Lyophilized)
浓度	≥8U/mg
储存温度	-20°C储存,避免反复冻融
运输条件	超低温冰袋运输
稳定性与储存	Store at -20℃ long term (36 months). Upon receipt, it is recommended to aliquot. Avoid freeze/thaw cycle.
分子类型	蛋白质

质检证书（CoA,COO,BSE/TSE 和分析图谱)

C of A & Other Certificates(BSE/TSE, COO):

输入批号以搜索分析图谱:

通过匹配包装上的批号来查找并下载产品的 COA，每批产品都进行了严格的验证，您可放心使用！

找到3个结果

批号(Lot Number)	证书类型	货号
ZJ25F0318828	分析证书	R748131
ZJ25F0318827	分析证书	R748131
ZJ25F0318826	分析证书	R748131

技术文档和文章

r748131_重组单体链霉亲和素 r msa 产品说明书.pdf

溶液计算器

摩尔浓度计算器

计算溶液所需的质量、体积或浓度。

质量

=

浓度

x

体积

x

分子量

g/mol

稀释计算器

计算配制储备溶液所需的稀释度。

浓度1（C1）

x

体积 1 (V1)

=

浓度 2 (C2)

x

体积 2 (V2)

复溶计算器

复溶计算器允许您快速计算试剂的体积，以复溶小瓶。只需输入试剂的质量和目标浓度，计算器将确定其余部分。

体积（添加到小瓶中）

=

质量（小瓶）

÷

所需的复溶浓度

货号 (SKU)	包装规格	是否现货
R748131-1mg	1mg	现货
R748131-5mg	5mg	期货
R748131-20mg	20mg	现货

重组单体链霉亲和素（r-mSA）

库存信息

库存信息

库存信息

基本描述

储存与运输

质检证书（CoA,COO,BSE/TSE 和分析图谱)

技术文档和文章

可替换产品

溶液计算器

摩尔浓度计算器

稀释计算器

复溶计算器